Design Optimization and Buckling Analysis of Pressure Vessel
Main Article Content
Abstract
Pressure vessels like pre-water heaters essentially heat exchangers that are used in closed power cycles. These pressure vessels are used to preheat the water fed into Boilers or heat the water before entering the boiler using expanded steam to increase the efficiency of the cycle. These heavy duty pressure vessels are in working condition throughout the year. The vessel strength will be reduced with time. This can be reduced by providing a winding coil around the vessel as a strip. The strip material will not affect the boiler but increases the life. The modeling was done by using Creo 2.0. Which is an advanced modeling software used in almost all the manufacturing industries. After the modeling the model was imported into the ANSYS 14.0. The linear buckling analysis of the pressure vessel will be done before and after the winding coil was placed at different load conditions and the maximum buckling load will be estimated. By considering some different type of materials to the mod el for showing the differences. Finally the results will be tabulated and graphs will be plotted.
Article Details
This work is licensed under a Creative Commons Attribution-NonCommercial 4.0 International License.
IJCERT Policy:
The published work presented in this paper is licensed under the Creative Commons Attribution 4.0 International (CC BY 4.0) license. This means that the content of this paper can be shared, copied, and redistributed in any medium or format, as long as the original author is properly attributed. Additionally, any derivative works based on this paper must also be licensed under the same terms. This licensing agreement allows for broad dissemination and use of the work while maintaining the author's rights and recognition.
By submitting this paper to IJCERT, the author(s) agree to these licensing terms and confirm that the work is original and does not infringe on any third-party copyright or intellectual property rights.
References
Prof. Vishal V. Saidpatil,Prof. Arun S. Thakare ‚Design & Weight Optimization of Pressure Vessel Due to Thickness Using Finite Element Analysis‛ accepted and published @ International Journal of Emerging Engineering Research and Technology (IJEERT), Volume 2, Issue 3, June 2014, PP 1-8, ISSN 2349-4395 (Print) & ISSN 2349-4409 (Online)
Rinu Cherian ‚Buckling Analysis Of Underwater Cylindrical ShellsSubjected To External Pressure‛ accepted and published @ International Journal of Innovative Research in Advanced Engineering (IJIRAE), ISSN: 2349-2163,Volume 1 ,Issue 10, (November 2014)
Prof. Nitinchandra R. Patel1, Avinash Vasava2, Jalesh Vasava3, Alpesh Kunapara4, Savan Patel ‘’DESIGN AND ANALYSIS OF PRESSUREVESSEL AMALGAMATING WITHSELECTION OF MATERIAL USED INMARINE APPLICATION‛ accepted and published @ International Journal of Innovative Research in Science, Engineering and Technology (IJIRSET), Vol. 2, Issue 6, June 2013, ISSN: 2319-8753
Siva Krishna Raparla,T.Seshaiah ‚DESIGN AND ANALYSIS OF MULTILAYER HIGH PRESSURE VESSELS‛ accepted and published @ International Journal of Engineering Research and Applications (IJERA) Vol. 2, Issue 1, Jan-Feb 2012, pp. 355-361, ISSN: 2248-9622
Han Xiao, Liu Botao, Lyu Shizeng1, Qi Yan and Guo Feng ‚Structure Design and Optimization of Vacuum Vessel for Spacecraft Thermal Test‛ accepted and published @ Applied Mechanics and Materials Vol. 390 (2013), pp 665-669 O,nline available since 2013/Aug/30
B. Mahendra, B. Ankanna, K.Tirupathi Reddy,M.Ravichandra ‚Modeling and Structural Analysis of A Pressure Hull under Dynamic Load‛ accepted and published @ International Journal of Modern Engineering Research (IJMER), Vol. 3, Issue. 6, Nov - Dec. 2013, pp-3552-3559, ISSN: 2249- 6645
Shaik Abdul Lathuef and K.Chandra sekhar ‚DESIGN AND STRUCTURAL ANALYSIS OF PRESSURE VESSEL DUE TO CHANGE OF NOZZLE LOCATION AND SHELL THICKNESS ‛ accepted and published @ International Journal of Advanced Engineering Research and Studies ,EISSN2249–8974, IJAERS/Vol. I/ Issue II/JanuaryMarch, 2012/218-221
K. Ramya Deepika, N. Jeevan Kumar ‚Design Optimization of a Pressure Hull for Dynamic Loading‛ accepted and published @ International Journal of Engineering Science and Innovative Technology (IJESIT)ISO 9001:2008 Certified, Volume 2, Issue 6, November 2013, ISSN: 2319-5967
Bandarupalli Praneeth, T.B.S.Rao ‚Finite Element Analysis of Pressure Vessel andPiping Design‛ accepted and published @ International Journal of Engineering Trends and Technology,Volume3Issue5, 2012, ISSN: 2231-5381
Apurva R. Pendbhaje Nitin Deshmukh, Rajkumar Patiln, Mahesh Gaikwad ‚ DESIGN AND ANALYSIS OF PRESSURE VESSEL‛ accepted and published @ International Journal of Innovative Research in Technology & Science(IJIRTS), VOLUME 2, NUMBER 3, ISSN:2321-1156